Deler/Oppgraderinger

Vis som Grid Liste

8 produkter

per side
Bruk stigende rekkefølge
  1. Kobling med Hann-QD og 1/8-Hunngjenger

    Kobling med Hann-QD og 1/8-Hunngjenger

    79,-

    Foster QD hannkobling med 1/8 hunngjenger.

    donePå lager
  2. GrovTec - Sling/Swivell Mount - 1,27cm og 1,9cm

    GrovTec - Sling/Swivell Mount - 1,27cm og 1,9cm

    129,-

    Lyst til å feste en sling eller tofot på din luftrifle men mangler fester? Da er dette produktet for deg!

    Med dette settet kan du enkelt og sikkert få montert på en sling eller tofot med swivel montering. GrovTec kittet her kommer med to skruer, en på 1.27cm og en på 1.9cm. Det følger også med spacere for ekstra god passform om du skulle trenge det. 

     


    donePå lager
  3. Kolbe til Crosman Pistoler

    Kolbe til Crosman Pistoler

    399,-

    Gjør om pistolen din til en liten carbine!

    Denne syntetiske kolben gir deg en ypperlig mulighet til å gjør om pistolen din til en Carbine slik at du får god støtte ved skyting både med kikkert og vanlige sikter. Den er laget i meget slitesterk polymer for å kunne tåle alle typer vær. Denne kolben gir deg virkelig en god blanding av både estetikk og funksjonalitet!

    Kompitabel med følgende modeller: 2250, 2240, 2300(alle modeller), BP2220, 1377C(American Classic Pump Pistol), 1322, PC77, 1720T, 2300KT og 2400KT

    donePå lager
  4. Hatsan AT-44/Bullboss Regulator

    Hatsan AT-44/Bullboss Regulator

    1090,-

    Regulator til din AT-44 tank. Gjør tanken din mer gjerrig på luft og kan skru ned trykket slik at du kan bruke lettere kuler og samtidig skyte snorbeint! Enkel å installere! 


    Under her har du instruksjoner på hvordan du installerer denne regulatoren, legger også en rekke filmer nederst. 


    Hatsan AT44

    1)      Unscrew airtube + cleaning
    2)      Mount regulator
    3)      Filling and draining air
    4)      Seting regulátor
    5)      Shipment contains

    1)      Before removing brass plug we need drain all air from airtube. When we unscrewing brass plug first time, airtube may need to be attached in a vice, but first try to unscrew the airtube in hand with a spanner. To avoid scratches and rotation airtube in vice is advisable to wrap the sandpaper around airtube(rough side out) and attached it. After unscrewing the brass  plug we clean o-ring and inside of the airtube. For cleaning we use a foam or lint free cloth. It is good to wash out the inside of the airtube with degreaser, or technical petrol, etc.


    2)      Remove the O-ring from brass plug. Spray regulators o-ring from outer side with silicone spray. Insert regulator into airtube so that it is possible to screw the brass plug and check the presence of the lower O-ring in the groove. By screwing plug we get regulator into correct position. Dont screw plug to the max, but leave a gap (between plug and airtube) about 0.5 mm


    3)      Fill airtube with air through quick fill. ALWAYS drain pressure from airtube by using drain valve which come with rifle, never drain air quickly it can cause damage to piston in regulátor.


    4)      The pressure setting is done by using a flat screwdriver in the upper part of the regulator.  When we setting regulator we rotate with  inside plastic screw with groove. The output pressure is showed by location colored grooves on the inner plastic screw. The total rotation range of the output pressure is in the range from 100 to 150 bar and is approximately 3/4 turn.
    Scale is starting on 100 bar (green color) and ends on 150 bar (red color). Scale is only approximate and course times may change slightly due to fatigue disc springs. Fill the airtube to the maximum pressure which is mentioned by manufacturer.


    5)  Regulator

    2 spare o-rings.

    Warning: You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings). Do not disassemble the regulator without previous approval, which will be awarded based on e-mail correspondence, where you provide the reason why it would be necessary to disassemble the regulator. In the case of breach this procedure you may damage the regulator function (fully assembled regulator is not simple and it is necessary to follow the correct procedure). For these reasons, the disassembly without previous consent,or failure exact installation procedure can not claim the warranty. Since regulator is not original part from the manufacturer’s, installation is on your own responsibility.

     

    Correct clean air tube and regulator:

     

    Remove regulator from air tube

    Assemble regulator

    Setting output pressure on regulator

    donePå lager
  5. Hatsan AT44/BT65 Charging Kit Dykkertank

    Hatsan AT44/BT65 Charging Kit Dykkertank

    999,-


    Spesielt designet til deg som ønsker å fylle luft fra en dykkertank!

    Kun til Hatsan AT44 og BT65.

    donePå lager
  6. Bakkolbe til Umarex RP5

    Bakkolbe til Umarex RP5

    499,-

    Enda mer stabilitet og treffsikkerhet til din RP5!

    RP5 er en svært presis og allsidig pistol fra Umarex som du virkelig kan gjøre personlig med diverse ekstra utstyr. 

    Denne kolben installeres enkelt på pistolen som gjør at den blir en "carbin" og gir deg enda mer treffsikkerhet!

    Kolben sitter svært godt i skulderen, er laget av metall og kan fint brukes av de fleste! Kombiner denne kolben sammen med optikk så har du maksimal treffsikkerhet!

    Kolben bygger 300mm lengde på pistolen.

    OBS: Rifla og siktet på bildet medfølger ikke!

    clearUtsolgt
  7. Hatsan BT-65/Galatian Regulator

    Hatsan BT-65/Galatian Regulator

    1090,-

    Regulator til din BT-65 tank. Gjør tanken din mer gjerrig på luft og kan skru ned trykket slik at du kan bruke lettere kuler og samtidig skyte snorbeint! Enkel å installere! 

     

    Under her har du instruksjoner på hvordan du installerer denne regulatoren, legger også en rekke filmer nederst. 

    It is appropriate before reading the instructions look at the video instructions and then read the instructions for avoiding common mistakes during installation
    Hatsan BT65

    1)      Unscrew airtube + cleaning
    2)      Mount regulator
    3)      Filling and draining air
    4)      Seting regulátor
    5)      Shipment contains

    1)      Before removing brass plug we need drain all air from airtube. When we unscrewing brass plug first time, airtube may need to be attached in a vice, but first try to unscrew the airtube in hand with a spanner. To avoid scratches and rotation airtube in vice is advisable to wrap the sandpaper around airtube(rough side out) and attached it. After unscrewing the brass  plug we clean o-ring and inside of the airtube. For cleaning we use a foam or lint free cloth. It is good to wash out the inside of the airtube with degreaser, or technical petrol, etc..

    2)      Remove the O-ring from brass plug. Spray regulators o-ring from outer side with silicone spray. Insert regulator into airtube so that it is possible to screw the brass plug and check the presence of the lower O-ring in the groove. By screwing plug we get regulator into correct position. Dont screw plug to the max, but leave a gap (between plug and airtube) about 0.5 mm

    3)      Fill airtube with air through quick fill. ALWAYS drain pressure from airtube by using drain valve which come with rifle, never drain air quickly it can cause damage to piston in regulátor.

    4)      The pressure setting is done by using a flat screwdriver in the upper part of the regulator.  When we setting regulator we rotate with  inside plastic screw with groove. The output pressure is showed by location colored grooves on the inner plastic screw. The total rotation range of the output pressure is in the range from 100 to 150 bar and is approximately 3/4 turn.
    Scale is starting on 100 bar (green color) and ends on 150 bar (red color). Scale is only approximate and course times may change slightly due to fatigue disc springs. Fill the airtube to the maximum pressure which is mentioned by manufacturer.

    5)  Regulator

    2 spare o-rings.
    Warning: You must keep maximum cleanness in the entire pressure system (airtube and outer o-rings). Do not disassemble the regulator without previous approval, which will be awarded based on e-mail correspondence, where you provide the reason why it would be necessary to disassemble the regulator. In the case of breach this procedure you may damage the regulator function (fully assembled regulator is not simple and it is necessary to follow the correct procedure). For these reasons, the disassembly without previous consent,or failure exact installation procedure can not claim the warranty. Since regulator is not original part from the manufacturer’s, installation is on your own responsibility.

     

    Correct clean air tube and regulator

    Install regulator

     

    Remove regulator from air tube

    Assemble regulator

    Setting output pressure on regulator

    clearUtsolgt
  8. Hatsan Løp til MOD135

    Hatsan Løp til MOD135

    499,-

    Ekstra Løp til Hatsan Mod 135. Leveres uten løpspakning.

    Sørger for nøyaktighet ved avfyring, lager minimalt med lyd og har sikte. 

     

     

    clearUtsolgt
Vis som Grid Liste

8 produkter

per side
Bruk stigende rekkefølge
Copyright © 2005-2018 Game-On AS. All rights reserved.